ESB Boba Fett BRL
(https://i.imgur.com/VcSsUh5.jpg)
Helmet
- Dome and cheeks must be painted an olive-green color (matte).
- Upper cheeks must be painted black (matte).
- Mandibles, brow, rear band, and key slots must be painted dark red (matte).
- The rear panels must be painted a dark blue-green color (matte)
- The right ear must be an earthen/tan color (matte) with a black upside-down “U” shape with inset white shape. The lower area of the ear cap and the upper area of the lower ear must be painted silver. This ear must have appropriate decals applied to it to match references be they painted or pre-made decals.
- The right ear must feature a rangefinder composed of a rangefinder stalk and rangefinder topper.
- Rangefinder stalk must be metallic.
- Rangefinder topper must be black with a translucent lower piece, and a black framed viewfinder window. Topper must have 2 functional alternating red LEDs on the top. White LED must be present in translucent block when RF is in the down position.
- The left ear must be an olive green color (matte) slightly more green than the dome and cheeks. A white upside-down “U” shape must appear at the top portion. This ear must have appropriate decals applied to it to match references be they painted or pre-made decals.
- 14 kill stripes must be painted on the left side of the dome. They must be painted yellow and fade starting with the 10th stripe to orange as they progress to the back of the helmet. They shall not touch the helmet brow.
- A borden connector greeblie must appear on the inner lower portion of the right cheek.
- The front left side of the dome must prominently feature the famous dent.
- The paint chipping and weathering on the helmet must be painted to match visual references as closely as possible both in color and in weathering pattern.
- The rear key slots must feature a Casio MQ-1 circuit board mounted behind the openings.
Flight Suit
- Must be a cotton or cotton blend one or two-piece garment colored blue-grey and must fit snuggly to the wearer.
- Must have long sleeves with short sleeves on top of them. Each short sleeve has a double row of stitching on the bottom edge.
- Cargo-style thigh pouches must be present with inward facing flaps.
- Each ankle must have shin pockets separated into two compartments.
- Must have ties around the ankles attached to the flight suit and must close via Velcro.
- Flight suit must be weathered, particularly around the bottom of the legs.
Pouches
- Must be the same blue/grey color as the flight suit and must be weathered.
- Must have 2 identical pouches with angled flaps at the top with the left pouch angling forward and the right angling back.
- Must hang by flaps that have the same full width as the pouch body and must be mounted to the back of the ammo belt.
Neck Seal
- Quilted neck seal made from the same tackle twill fabric or material of similar appearance as the vest featuring five horizontal ribs.
- Must close in the front with Velcro or hooks.
Flack Vest
- Must be quilted and made of tackle twill or a material of similar appearance in a very light grey color.
- Must have two short shoulder tabs to mount the shoulder armor. These must be quilted and feature vertical ribs running from the bottom to the shoulder seam.
- Must be short enough to stop before hitting the girth belt and must close in the back.
- Must have slits cut in the back to feed the jetpack harness straps through.
Boots
- Must be made of grey canvas or similar material with black leather or leather-like piping running in four lines from toe to ankle.
- Must have black U-shaped cutouts on each side.
- Must have white, flat soles.
- Must have two spikes attached at the toe via a plate. Spikes must be metal or appear to be metal.
- Must be weathered to match references.
Chest Armor
- Consists of collar armor, right and left chest plates, ab plate, and center diamond.
- Must appear to be at least 3mm thick with rounded edges.
- Chest plates, collar plate, and ab plate must be painted a medium-dark green (matte). All plates must feature exposed silver damage. Left chest plate and ab plate must also feature exposed yellow damage.
- Chest diamond must be painted a more intense/ slightly darker green (matte/satin) than the other chest armor and must feature an inset, silver/white rectangle and match visual references.
- Right chest plate and collar must be weathered to appear slightly darker than the other plates.
- All plates must be painted and weathered to match references both in color and weathering pattern.
- Left chest plate must feature two cut-out horizontal bars with the upper bar being narrower than the bottom. They must be backed by an illuminated red, flashing display.
- The right breast plate must feature a decal in the upper right. This can be painted to match references or may be a pre-made decal.
- All armor must attach securely to the vest with proper spacing.
- Collar armor must connect to back plate via 4 square armor studs. The wearer's outermost right stud will have a red top/cap. The wearer's outermost left stud (cape stud) will be painted matte black.
Back Armor
- Must appear to be at least 3mm thick with rounded edges.
- Must be medium-dark green (matte) and must feature exposed silver damage.
- Must be painted and weathered to match references both in color and weathering pattern.
- Must have two rectangular slots over the shoulder blades to allow the jetpack harness straps to feed through.
- Must have extended upper “collar” portion.
- Must have curved cutout at the bottom.
Shoulder Armor
- Must appear to be at least 3mm thick with rounded edges. Must have six points and must curve around the upper arm.
- Right shoulder must be orange-yellow (matte). Left shoulder must be light/golden yellow (matte)
- Must be painted and weathered to match references both in color and weathering pattern.
- Left shoulder must feature a red ESB-specific Mythosaur skull set on a white background.
Cod Armor
- Must appear to be at least 3mm thick with rounded edges. Must wrap around the front of the body and connect to the kidney armor via 2 square silver studs.
- Cod armor must be painted medium-dark green (matte) and must feature exposed silver and yellow damage.
- Must feature a large dent on the left side of the raised front plate.
- Must feature two connected rectangular shapes on the right hand side.
- A grey/white nylon or elastic strap runs from the bottom of the cod armor to the bottom of the kidney armor.
Kidney Armor
- Must appear to be at least 3mm thick with rounded edges. Must wrap around the back of the body and connect to the cod armor via 2 square silver studs.
- Kidney armor must be painted medium-dark green (matte) and must feature exposed silver and yellow damage.
Knee Armor
- Must appear to be at least 3mm thick with rounded edges. Must curve under the bottom of the knee at the bottom.
- Knee armor must be painted orange-yellow and must feature exposed silver damage.
- Must be painted to match references in both color and weathering pattern.
- Right knee must feature a large dent on the lower left. Left knee must feature a dent on the upper right.
- Left knee must feature 2 identical silver cylindrical dart launchers on the outside. The right knee must feature 1 cylindrical dart launcher and 1 smaller, conical, tapered metal piece on the outside with the dart launcher being placed below the conical piece.
- The inner section of both knees must feature an upside down “F” shape that matches references.
Left Gauntlet
- Must be a medium green (matte) distinguishable from the armor and must feature exposed sliver damage and a large dark grey and silver damaged patch on the inner portion of the gauntlet
- Must be painted to match references in both color and weathering pattern.
- Must feature a MQ-1 Calculator keypad on the wrist, a bronze/brass dental expander mounted above the keypad, and a rocket mounted on the top of the gauntlet. All pieces must be painted to match references in color and weathering pattern.
- Flamethrower is to be mounted on the outer portion of the gauntlet and must be constructed and painted to match visual references.
- The lower shell of the gauntlet must feature 3 indents on the inner portion.
Right Gauntlet
- Must be a medium green (matte) distinguishable from the armor and must feature exposed silver damage.
- Must be painted to match references in both color and weathering pattern.
- Must feature 4 small silver darts mounted towards the front, two silver switches mounted facing the outside of the gauntlet, and whipcord housing on the outside of the gauntlet. All pieces must be painted to match references in color and weathering pattern.
- One braided rubber hose is mounted on the back of the gauntlet and must run up the short sleeve of the flight suit.
Jetpack
- Must be a medium green (matte) distinguishable from the armor with red and yellow accent detailing and must feature exposed silver damage.
- Must be painted to match references in both color and weathering pattern.
- Must have red “piano keys” mounted horizontally across the top of the main body.
- Must have a silver beacon light with a black top on the left and a silver stabilizer on the right.
- The main body must feature a white vertical half-oval decal on the lower left and two horizontal red-brown stripes on the lower right.
- Jetpack must fit snugly against the back plate without sagging and must be supported by white nylon/canvas straps which extend from the slots in the back plate.
Ammo Belt
- Must be a medium brown leather or leather like material that secures via Velcro in the rear.
- Must feature 7 ammo pouches with 4 on the left and 3 on the right. Must have snaps on the 2nd and 4th pouches (from left to right) Optional snap on the 7th pouch.
- Pouches and belt must feature stitching consistent with references.
- Must have 2 decorative grommets on the back.
Gloves
- Must be dark grey cotton with quilted patches on the back of each hand and on the fingers.
- Patches on the back of each hand must feature vertical stitches and the patch on the right glove must be larger than the patch on the left.
- Must have a white cuff on each glove.
Cape
- Must be a heavy cotton, linen, canvas, or wool material, khaki/tan in color with an orange-brown vertical stripe. Must be approximately 30” wide by 36” long.
- Must be hung from the left shoulder by the outermost stud.
- Must be tattered and weathered to match references.
Girthbelt
- Must be a red-brown multi-strand rope that wraps around the body with 4 silver buckles in the rear.
- Must have a gap in the rear with the buckles being connected by black straps.
Wookie Braids
- Must have one black, one blonde, and one grey braid hung from the right shoulder. The black braid should be a closed loop.
- Braids must be ornamented to match visual references.
Shin Tools
- Must have 1 Sonic Beam Weapon (Patterson Squeegee), 1 Anti-Security Blade (Cutoff portion of the Patterson squeegee combined with 2 stylus brush parts), 1 Survival Knife (Patterson chemical stirrer), and 1 Jetpack Adjustment Tool (silver metal cylinder).
- Must be constructed, painted, and weathered to match references in color and weathering pattern.
Sidearm Holster
- Must be a Nemrod holster or replica made from a solid material (plastic, fiberglass, rubber, etc.)
- Must loop around ammo belt via a black strap on the right side.
EE-3 Blaster Carbine
- Must be a Webley No. I Mk I Flare gun or replica constructed to match references.
- Must feature a smooth barrel constructed to match visual references.
- Must have an ASI or similar 4x20 scope mounted to the top via brackets.
- Must have accurate plug greeblies mounted to scope brackets and stock greeblies. The center stock greeblie must have a red border.
- Grip must be painted bronze/brass.
- Must feature a medium-dark brown leather strap.
- Must be painted and weathered to match references in color and weathering pattern.
Sidearm
- Must be a Pulce 40 spear gun or replica
- Must be painted reddish-brown and silver.
- Must be painted to match references both in color and weathering pattern.