(https://i.imgur.com/qaiXftA.png)
Boba Fett ROTJ BRL
Helmet
- Dome and cheeks must be painted an olive-green color (matte).
- Upper cheeks must be painted a dark blue-green (matte).
- Mandibles, brow, rear band, and key slots must be painted dark red (matte). Key slots are weathered metallic, like the earcaps
- The rear panels must be painted a medium green color (matte)
- The earcaps must painted silver and weathered to match references.
- 18 kill stripes must be painted on the left side of the dome. They must be painted dark orange. They shall not touch the helmet brow.
- A borden connector greeblie must appear on the inner lower portion of the right cheek.
- The front left side of the dome must prominently feature the famous dent.
- The paint chipping and weathering on the helmet must be painted to match visual references as closely as possible both in color and in weathering pattern.
- The rear key slots must feature a Casio MQ-1 circuit board or resin copy mounted behind the openings.
- Two red #15 micromega dental files or cast replicas are centered in the bottom 2 keyslots
- Helmet must have a rangefinder and stalk. The rangefinder’s upper portion must be painted black and the lower portion must be clear/transluscent.
- Rangefinder DOES NOT have a viewfinder
- Rangefinder must have functional LEDs with alternating red on the top of the housing and a white light in the translucent perspex block.
Flight Suit
- Must be a cotton or cotton blend one or two-piece garment colored light grey and must fit snuggly to the wearer.
- Must have long sleeves with short sleeves on top of them.
- Cargo-style thigh pouches must be present with inward facing flaps.
- Each ankle must have shin pockets separated into two compartments.
- Flight suit must be weathered, particularly around the bottom of the legs.
Spats
- Must have flared ankle spats of an light beige
- Must be weathered to match references
Hip Pouches
- Must be khaki/beige color and must be weathered.
- Must have angled flaps at the top with both left and right pouches angling backwards.
- Must hang by flaps that have the same full width as the pouch body and must wrap around the ammo belt.
Neck Seal
- Quilted neck seal made from the same tackle twill fabric or material of similar appearance as the vest featuring five horizontal ribs.
- Closure in front
Flak Vest
- Must be quilted and made of tackle twill or a material of similar appearance in a very light grey color.
- Must have two short shoulder tabs to mount the shoulder armor. These must be quilted and feature vertical ribs running from the bottom to the shoulder seam.
- Must be short enough to stop before hitting the girth belt and must close in the back.
- May have slits cut in the back to feed the jetpack harness straps through.
Boots
- Must be made of grey canvas or similar material with black leather or leather-like piping running in four lines from toe to ankle.
- Must have black U-shaped panels on each side.
- Must have white, flat soles.
- Must have two spikes attached at the toe via a plate. Spikes must be metal or appear to be metal.
- Must be weathered to match references.
Chest Armor
- Consists of collar armor, right and left chest plates, ab plate, and center diamond.
- Must appear to be at least 3mm thick with rounded edges.
- Chest plates, collar plate, diamond, and ab plate must be painted a medium-dark green (matte). All plates must feature exposed silver and yellow damage.
- Chest diamond must feature an inset, silver rectangle
- All plates must be painted and weathered to match references both in color and weathering pattern.
- Left chest plate must feature two cut-out horizontal bars with the upper bar being narrower than the bottom. They must be backed by an illuminated red, flashing display.
- The right breast plate must feature a Jaster's Feather decal in the upper right. This can be painted to match references or may be a pre-made decal.
- All armor must attach securely to the vest with proper spacing.
- Collar armor must have 2 square silver studs on each side of the neck where the collar connects with the backplate. These do not have to be functional.
Back Armor
- Must appear to be at least 3mm thick with rounded edges.
- Must be medium-dark green (matte) and must feature exposed silver and yellow damage.
- Must be painted and weathered to match references both in color and weathering pattern.
- Must have two rectangular slots over the shoulder blades to allow the jetpack harness straps to feed through.
- Must have extended upper “collar” portion.
- Must have curved cutout at the bottom.
Shoulder Armor
- Must appear to be at least 3mm thick with rounded edges. Must have six points and must curve around the upper arm.
- Must be painted golden yellow (matte).
- Must be painted and weathered to match references both in color and weathering pattern.
- Left shoulder must feature a red ROTJ-specific Mythosaur skull set on a white background.
Cod Armor
- Must appear to be at least 3mm thick with rounded edges. Must wrap around the front of the body and connect to the kidney armor via 2 square silver studs. One stud on each side and does not need to be functional.
- Cod armor must be painted medium-dark green (matte) and must feature exposed silver and yellow damage.
- Must feature a large dent on the left side of the raised front plate.
- Must feature two connected rectangular shapes on the right hand side.
- A dirty white nylon or elastic strap runs from the bottom of the cod armor to the bottom of the kidney armor.
Kidney Armor
- Must appear to be at least 3mm thick with rounded edges. Must wrap around the back of the body and connect to the cod armor via 2 square silver studs.
- Kidney armor must be painted medium-dark green (matte) and must feature exposed silver and yellow damage.
Knee Armor
- Must appear to be at least 3mm thick with rounded edges. Must curve under the bottom of the knee at the bottom.
- Knee armor must be painted golden yellow and must feature exposed silver damage.
- Must be painted to match references in both color and weathering pattern.
- Right knee must feature a large dent on the lower left.
- Left knee must feature 2 identical silver cylindrical dart launchers on the outside. The right knee must feature 1 cylindrical dart launcher and 1 smaller, conical, tapered piece on the outside with the dart launcher being placed below the conical piece. The launchers and conical piece must appear to be metal.
- The inner section of both knees must feature an upside down “F” shape that matches references.
- Knee elastic must be dirty white and match visual references
Left Gauntlet
- Must be painted a dark red (matte) and must feature exposed sliver damage.
- Must be painted to match references in both color and weathering pattern.
- Must feature a MQ-1 Calculator keypad or replica on the wrist shelf, a bronze/brass dental expander or replica mounted above the keypad, and a rocket mounted on the top of the gauntlet. All pieces must be painted to match references in color and weathering pattern.
- Flamethrower housing is to be mounted on the outer portion of the gauntlet and must be constructed and painted to match visual references. Must feature two exposed nozzles on the end and two pushbutton switches on the top of the housing.
- The lower shell of the gauntlet must feature 3 indents on the inner portion.
- Must feature a round, flat, red LED near the elbow.
Right Gauntlet
- Must be painted a dark red (matte) and must feature exposed silver damage.
- Must be painted to match references in both color and weathering pattern.
- Must feature 4 small silver darts mounted towards the front, two silver switches mounted facing the outside of the gauntlet, and whipcord housing on the outside of the gauntlet. All pieces must be painted to match references in color and weathering pattern.
- One braided rubber hose is mounted on the back of the gauntlet and must run up the short sleeve of the flight suit. Two additional braided rubber hoses are mounted to the rear of the cord housing and must run up the short sleeve of the flight suit.
Jetpack
- Must be painted medium blue, sliver, white, black, yellow, orange, and red.
- Must be painted to match references in both color and weathering pattern.
- Must have a silver beacon with black detailing on the left and a silver stabilizer on the right
- The main tank and rocket must feature a black horizontal stripe each. The side tanks must feature black horizontal stripes at the tops interrupted by black decals that match references. The raised white portions on the body of the jetpack must feature black decals that match references.
- Jetpack must fit snugly against the back plate without sagging and must be supported by white nylon/canvas straps which extend from the slots in the back plate.
Ammo Belt
- Must be a medium brown leather or leather like material that secures via Velcro in the rear.
- Must feature 8 ammo pouches on the front of the belt.
- Pouches and belt must feature stitching consistent with references.
- Must have 6 decorative grommets on the back.
Gloves
- Must be light grey cotton with quilted patches on the back of each hand and on the fingers.
- Patches on the back of each hand must feature vertical stitches and the patch on the right glove must be larger than the patch on the left.
- Must have a white cuff on each glove.
Cape
- Must be a heavy cotton or canvas material, olive green in color. Must be approximately 30” wide by 36” long.
- Must be hung from the left shoulder by the outermost stud.
- Must be tattered and weathered to match references.
Girthbelt
- Must be a dark red 14 multi-strand rope that wraps around the body with 4 silver buckles in the rear.
- Must have a gap in the rear with the buckles being connected by black straps approximately 6"-8" long.
Wookie Braids
- Must have a black and black w/blonde braid with a looped design and decorative tail with leather knot ornaments This braid will also have a grey braid tail hanging forward. One blonde, and one brown braid also of looped design will hang from the right shoulder.
- Braids must be ornamented to match visual references.
- Braids will feature the correct blue, red, black, and white ties.
Shin Tools
- Must have 1 Sonic Beam Weapon (Patterson Squeegee), 1 Anti-Security Blade (Cutoff portion of the Patterson squeegee combined with 2 stylus brush parts), 1 Survival Knife (Patterson chemical stirrer), and 1 Jetpack Adjustment Tool (silver metal cylinder).
- Must be constructed, painted, and weathered to match references in color and weathering pattern.
EE-3 Blaster Carbine
- Must be a Webley No. I MK I Flare gun or replica constructed to match references.
- Must feature a ROTJ barrel constructed with t-tracks to match visual references.
- Must have an ASI or similar 4x20 scope mounted to the top via brackets.
- Must have accurate gun body and stock greeblies.
- Must be painted and weathered to match references in color and weathering pattern.