Boba Fett (Repainted) – The Mandalorian S2

Helmet

• Dome and lower cheeks must be painted a matte medium green.
• Upper cheeks are painted a matte dark blue green in color.
• Mandibles, brow, and rear band , including the key slots are painted a matte dark red.
• The right ear must be an earthen/tan color (matte) with a black upside-down “U” shape with inset white shape. This ear must have appropriate black decals applied to it to match references be they painted or pre-made decals.
• The left ear must be matte dark green in color. A white upside-down “U” shape must appear at the top portion. This ear must have appropriate black decals applied to it to match references be they painted or pre-made decals.
• Rear panels are painted a matte medium green.
• 19 Killstripes are present on the left side of the helmet dome.  The first 18 are painted red-orange with the last one being black in color and do not touch the brow of the helmet.
• Helmet dome must feature two turn signal style triangles at the forehead of the helmet that are smaller and spaced further apart than previous Boba Fett helmets.
• The right turn signal is painted a medium red and the left is a navy blue.
• The back of the helmet must feature 6 key slots in a rectangular recessed area.  The bottom two keyslots have a small cylinder like greeblie present in the middle of the keyslot.
• A borden connector greeblie must appear on the lower portion of the right cheek of the helmet.
• The front left side of the helmet dome must prominently feature a smaller version of the famous dent.
• The paint chipping and weathering on the helmet must be painted to match visual references of the re-painted Boba Fett helmet as closely as possible in weathering, damage, and overall wear.
• Rangefinder stalk is silver in color while the helmet rangefinder topper is painted black in color and features two small parallel holes on the right side for two red led lights.  The underside of the rangefinder must feature a clear perspex block, set deeper into the topper than the original helmets and a smaller viewfinder painted black attached to the underside of the block.

BRL Level Approval:

• The borden connector greeblie is placed further away from the upper cheek than the live action death watch helmet.
• Cylinder greeblies on the keyslots of the helmet are painted silver.
• Rangefinder stalk is made from metal and  has the ability to rotate forward 90 degrees, activating the lights on the topper.
• Paint texture will be closely scrutinized for texture and placement consistent with that seen in the show.

Undersuit

• Undersuit is made of black and/or linen blend fabric.
• Neck of the undersuit is a rolled cowl that wraps loosely around the wearer’s neck.
• The undersuit is loosely fitted to the wearer.

Gloves & Handplates

• Gloves are made of leather or leather like material and are two tone in appearance.  A black outer glove is worn with the fingers cut off just past the knuckle.  The fingers of the gloves themselves are dark brown in color.
• Skin is not visible between the flightsuit and wrist.
• A symmetrical armor plate, like the ones worn by both versions of season 1 Din Djarin are present on the back of the hands.

BRL Level Approval:

• Gloves are made of leather.
• Handplates are made of rubber.

Pants & Waist Sash

• Loosely fit, Hakama style pants made with the appearance of black raw silk.
• Closure is hidden by the waist sash.
• Waist sash also must have the appearance of black raw silk.
• Sash features two hanging pieces off the right hip.
• The ends of the sash must be tattered in appearance.

BRL Level Approval:

• Both pants and waist sash are made from raw silk.
• Hanging pieces from the waist sash fall to the shin level of the wearer.

Boots

• Black boots that are rubber at the sole and base.
• Black leather or leather like boot spat that is approximately knee height that covers the top of the foot around the sides to the back and straps underneath the center of the bottom of the boot.
• Toes of boots have lined toe covers above the visible tread of the front of the boot.
• Heel and toe of the boot also must feature raised lines consistent with reference images.

BRL Level Approval:

• Boots are the Nortiv 8 boot or acceptable replica.
• Boot spat is made of black leather.

Flak Vest

• Flak vest is black in color and made from a cotton weave fabric
• Must have two short sleeves to mount the shoulder armor. These must be quilted and feature horizontal ribs on the body of the tab.  Each sleeve is separated from the body of the vest by piping.
• Sleeves are sized larger than the shoulder armor and come down on the wearer about mid bicep.
• Edges of each sleeve must feature 3 lines of horizontal stitching.
• Vest body is free from decorative stitches with the exception being one horizontal rib stretched across the collar of the vest in line with the top of the sleeves.
• Vest closes at the back.
• Vest ends just above the wearer’s naval.

BRL Level Approval:

• Vest must line up with the bottom of the wearer’s ab plate.

Girth Belt

• Made of black, white and brown diagonal striped paracord making the belt approximately 4.5” wide.
• Fits snugly around the wearers waist and closes at the back with a black panel hiding the method of securement.

Ammo Belt

• The ammo belt is dark brown in color and made of leather or leather-like material weathered consistent with the reference images.
• The center of the belt has a rectangular belt buckle weathered gold in color.  The buckle features three indented circles in the lower right hand corner.  These circles are separated by three indented lines, bisecting the middle of the belt straight, then at an angle.  The bottom line must be wider than the two higher up.  Two raised dumbbell shaped details are present in the top left corner of the buckle above the lines.  There is also an indented border that goes around the entirety of the buckle.
• To the wearer’s left of the buckle is a weathered gold stud.
• Two dark brown pouches are present on either side of the belt buckle.  Three pouches feature an angled flap down to the wearer’s right, while the pouch immediately to the left of the belt buckle has a straight flap.  Light colored stitching outlines the flaps on the pouches.

BRL Level Approval:

• Belt and pouches are made of leather.
• Belt buckle and stud are made of metal.

Thigh Holster

• The holster is made of leather or leather like material and is dark brown in color.
• The holster must hang from the right side of the ammunition belt via a strap, made of the same material as the holster.
• Four weathered brass studs are present on the connecting strap from the belt to the holster in a four square pattern.
• Stitching is present along the back edge of the holster.
• There is a strap attached to the front and back of the holster to hold the sidearm in place with a matching brown circular end and next to that a silver metal stud to secure the strap.

BRL Level Approval:

• Thigh holster and straps are made of leather.

Chest Armor

• Consists of collar armor, right and left chest plates, ab plate, and center diamond.
• Must appear to be 3mm thick with squared, hard edges.
• Armor is painted a matte medium green.  Armor has been repainted, but some edge wear and surface weathering is evident.  Armor must feature a rough texture consistent with screen used references.
• Left chest plate must feature two, cut-out horizontal bars with the upper bar being narrower than the bottom bar.  They must be backed by an illuminated red, flashing display.  Dents are seen on this chest plate in the upper left corner, with two more present on the left side of the plate.
• Right chest plate must feature a re-painted “Jaster’s Crest” sigil in the upper right corner.  The sigil can be painted to match references or be a pre-made decal.  There are no dents present on the right chest plate.
• Collar armor abuts up to the backplate with a seam between the two plates featuring two gray studs at the top edge of the collar plate on either side of the wearer.
• Ab plate is a standard 9 sided Modern ab plate featuring two dents on the top and bottom of the right side and 3 small closesly spaced holes on the left.
• Ab plate detail holes must must be drilled out to expose the black flak vest beneath without exposing attachment methods.
• Ab plate sits near the edge of the flak vest with no more than 10mm of gap to the end of the garmet.

BRL Level Approval:

• “Jaster’s Crest” in the upper right hand corner of the right chest plate is painted and not a decal.
• Paint texture will be closely scrutinized for texture and placement consistent with that seen in the show.

Back Armor

• Must appear to be at least 3mm thick with squared, hard edges.
• Two dents are present on the back plate’s outside edges. One dent is on the upper left outside edge, below the jetpack harness opening. Another can be found on the lower right hand edge of the backplate.
• Back armor has been repainted a matte olive green.  Armor has been repainted, but some edge wear and surface weathering is evident.
• If the wearer does not have a jetpack the back plate must feature a rectangular hole cut out of the middle of the back.
• Back armor must feature a rolled collar at the base of the neck.
• Must feature a half circle cutout at the base of the back armor.

Shoulder Armor

• Must appear to be at least 3mm thick with hard, sharp edges.  Armor has to feature six points and be worn around the wearer’s deltoid muscle.
• Shoulders have been repainted light/golden orange, but some edge wear and surface weathering is evident.  Armor must feature a rough texture consistent with screen used references.
• Left shoulder features the ROTJ variant of the Mythosaur sigil, in a medium red backed by an off white background.  Decal or painted on is acceptable.
• Dents are only featured on the right shoulder plate with a large crater on the upper right hand side, two small chips on the top and front facing edge of the shoulder, and a smaller crater on the lower right hand side of the plate.

BRL Level Approval:

• Mythosaur sigil on the left shoulder is painted and not a decal.
• Paint texture will be closely scrutinized for texture and placement consistent with that seen in the show.

Left Gauntlet

• Gauntlet construction is clam shell style without any visible means of closure.
• Gauntlet body has been repainted dark burgundy, but must feature some edge and surface wear consistent with references.
• An MQ-1 keypad, red in color to match the gauntlets with the buttons painted silver, and is visible in the forward most recessed section of the gauntlet.  Immediately above the keypad is a silver colored greeblie resembling the Glenross dental expander.
• On top of the gauntlet is a repainted rocket with the tip and tail painted silver, the body painted black, and the nose cone painted copper.
• The outside of the gauntlet features a weapon housing, formerly the ROTJ style flamethrower.  The housing is rectangular in shape, stretching slightly longer than the length of the gauntlet, with an angled front down toward the user.  Two muzzles are seen protruding from the front of the housing with the top muzzle slightly more forward than the bottom.
• Two push button style switches are present on the top of the weapon housing with black plastic circular switches on top.
• A small, round, red LED is present on the back inside corner of the gauntlet, next to the rocket.
• On the inside upper shell of the gauntlet is the battery cover greeblie, under the rocket.
• Lower shell of the gauntlet must feature 3 indented sections on the inner portion.

BRL Level Approval:

• Push button style switches on the top of the weapon housing have black plastic circular tops.
• Base of the red LED is metal.
• Muzzles coming out of the front of the weapon housing are made of metal.
• The tail of the rocket features a conical end.

Right Gauntlet

• Gauntlet construction is clam shell style without any visible means of closure.
• Gauntlet body has been repainted dark burgundy in color and must feature edge and surface wear consistent with the references.
• Front of the gauntlet features four silver darts facing outwards with an ovular gray greeblie mounted just above the darts.
• A small rectangular indent is present at the forefront of the right gauntlet, just above the wrist opening and is painted black.
• Two small momentary push buttons are visible on the top outside edge of the gauntlet.  These buttons are smaller, and squatter than previous OT versions of this greeblie.
• Gauntlet features three hoses covered in black fabric.  One is attached directly to the rear of the gauntlet via a tapered block with no apparent connection hardware.  The other two connect to the back of the flame thrower unit, which used to be the whipcord housing with hardware painted the same color as the gauntlet.  The hoses reach up and terminate under the rear of the shoulder armor, into the vest of the wearer.
• Lower shell of the gauntlet has 3 rectangular indentations on the inside forearm of the gauntlet just below the upper and lower seam of the gauntlet.

BRL Level Approval:

• Darts are made of metal.
• Momentary push buttons are functional.
• At the top of the gauntlet, just before the hose attachment, is a raised rectangle painted black.

Knee Armor

• Two modern style knee plates are present on this version of Boba Fett worn around the top of the shin just below the knee.
• The knee plates have been re-painted a golden yellow and must feature edge and surface wear consistent with the references.  The right knee exhibits a dent in the lower right hand side of the front facing plate.  The left knee is free from physical damage.
• The outer section of each knee plate has two greeblies painted silver with the left knee featuring two identical cylindrical dart launchers, and the right knee having a tapered cone greeblie above a single cylindrical dart launcher.

BRL Level Approval:

• Knee darts are made of metal.

Blaster Pistol

• The base of the blaster pistol is a Sedgley Mark IV Flare gun or acceptable replica.  The extended barrel, upper barrel, and optics were added to the base flare pistol.
• The extended lower barrel, tapers slightly back into the base flare pistol.  The second, higher barrel, runs parallel the the lower barrel, and ends in a sharp angle, just beyond the breech of the flare pistol.
• Two brackets connect the two barrels.  One at the front, slightly pulled back from the muzzle, and another at the breech of the flare pistol.
• At the top of the breech bracket, a small scope can be seen ending in a sharp angle right at the bracket.  While the front of the scope does not extend past middle bracket, the rear stops just before the breech of the pistol.
• Middle of the scope features a ring greeblie, while the end closest to the user has a slight taper forward.
• Grip of the pistol is the same of that as the Sedley flare pistol, but the front portion ends in a hard angle instead of a rounded edge, ending just in front of the middle bracket.
• Trigger is the same as the Sedley, just with added grooves to the press.
• Grip inlays are wood in appearance with a circular greeblie inset inside another circular greeblie towards the bottom.
• A ring and swivel are present in indented section of the grip at the very bottom.
• Pistol is two-toned in color with the rear section being black in color and the front being a weathered bronze.  Flecks of weathered steel are also visible, particularly at the base of the lower barrel, in front of the breech.

EE-3 Blaster Carbine

• Must be a Webley No. 1 MK 1 shoulder stocked flare gun or replica constructed to match references.
• Body of the blaster is black in color and features a weathered brass grip.
• Featured above the grip and trigger are a crankshaft and piston half, or replica, from the Revell visible V-8 engine model kit.
• Barrel and forward cone of the blaster is gunmetal in color with grooves in a similar style to the ROTJ EE-3.
• Stock is walnut in color with appropriate inset greeblies painted gunmetal in color.
• At the top of the blaster is a Lyman all American 4x rifle scope, or replica, attached with two detachable scope rings painted black.

*Optional Accessories*
Jetpack

• Jetpack follows the traditional Boba Fett Jetpack design of the Mitrinomon Z-6 jetpack with a raised center tank and two fuel tanks on either side of the center tank.
• Jetpack must feature a center missile with appropriate collar, and base.
• Two directional thrusters are present on either side of the jetpack.  The main body of the thruster is painted a medium green, with trapezoid indents around the cone of the thruster painted golden yellow.  Greeblies, metallic silver in color, are connected to the outside of the sphere of the thruster, while a metallic silver circular greeblie is inset into the face of the sphere with a red cross inside of that.
• A jetpack beacon and stabilizer are present on the flat section above the center tank.  The beacon is on the left of the missile, while the stabilizer is on the right. Both must be metallic silver in color and the jetpack beacon must feature a brass top.
• Piano keys are present on either side of the center tank, stretching horizontally out to either side and are painted dark red in color.
• The bottom of the jetpack has a winged exhaust vent in the middle of the pack.  Two greeblies are seen on either side of the pack with a white plastic push button to the right of the exhaust vent, and the female half of the XLR connector on the left.
• The Mandalorian version of this jetpack features a repair patch on the main center tank running upward left to right and contours directly to the jetpack’s surface.
• Jetpack must sit securely to the wearer and must not sag or otherwise appear loose in its connection.
• Jetpack colors follow the ESB Hero scheme in spirit, but is an entirely different paint job.
• Main body of the jet pack is a medium green and metallic silver for the weathered sections.
• Missile of the jetpack is a medium green, with the band below the nose cone painted dark gray.  Jetpack collar is steel in color with the ring above that painted a golden yellow.
• Three small white circles are painted on either side and the middle of the missile base.

BRL Level Approval:

• Missile of the jetpack features a blunt tip, unlike the sharper missiles seen in the OT.
• Missile collar, outermost circular greeblies on the thrusters, winged exhaust vent and interior thruster circular greeblies are made of metal.
• Jetpack repair patch must feature attachment rivets.
• Jetpack beacon and stabilizer are metal.
• Jetpack beacon top glows orange due to small light activated inside.