(Unless otherwise noted, the requirements are used for both real world and animated versions of this costume.)

• Helmet
  • An animated Deathwatch style helmet must be used.
  • The dome, face, and back is painted gunmetal grey or charcoal grey. The mandibles, key slot indentation, and band are Rustoleum brilliant blue. The cheeks and light gray or silver.
  • The helmet should have the narrower design with the longer face and the T should come to points at the ends.
  • There are no diamonds on the forehead of the helmet.
  • The right earcap must match the left.
  • There is no RF for Season 2 Death Watch Grunts.
• Shoulder Plates
  • The shoulders are stylized shape, slightly curving inward on the sides.
  • They are gunmetal grey or charcoal grey in color.
  • Symbols must match references in color and design.
• Chest Armor
  • Chest armor must be the animated Deathwatch style and consist of two chest plates, ab plate, diamond, and collar plate.
  • Plates are gunmetal grey or charcoal grey in color and weathered through slightly.
  • The chest slots are not to be cut out. The slots should be painted with red paint.
• Back Plate
  • Must be the animated Deathwatch style armor.
  • It is gunmetal grey or charcoal grey in color.
• Cod Armor
  • The cod armor is in a stylized shape more of a triangle than the normal cod shape.
  • It is gunmetal grey or charcoal grey in color and weathered through slightly.
• Thigh Armor
  • Must be the animated Deathwatch style armor.
  • The plate rides on the outside of the thigh rather than on the front of the thigh.
  • The holsters are built into the thigh plate and appear as part of the armor.
  • They are gunmetal grey or charcoal grey in color.
• Knee Plate
  • Must be the animated Deathwatch style armor.
  • The base color is flat silver/light grey.
• Shin Armor
  • Must be the animated Deathwatch style armor.
  • They are gunmetal grey or charcoal grey in color.
• Boot Armor
  • Must be animated Deathwatch style armor.
  • Near the ankle, the armor should be gunmetal grey or charcoal grey in color.
• Hand Plates
  • The hand plates are a completely custom design in a ‘tombstone’ shape.
  • They are gunmetal grey or charcoal grey in color and weathered slightly through.
• Gauntlets
  • The gauntlets are a completely custom design.
  • They are a set of clamshell cylinder gauntlets.
  • There is a notch on the top which is approximately 3-inches wide and 1-inch long.
  • In front of it is a long box that is ½-inch high, 3-inches wide, and runs ½-inch from the edge of the elbow and wrist of the gauntlet.
  • Another ½-inch box fits on the top that is approximately 3/8ths of the length of the original box.
  • The edges all fade with a 60-degree edge except for the top that is a 45-degree angle.
  • There are two small rectangles on the top outside of each gauntlet.
  • They are flat silver/light grey in color and slightly weathered through.

• Flight Suit
  • The flight suit will be blue in color and have the standard Mandalorian double-sleeve.
  • The neck seal will be a straight tube with light padding inside of it. It has a small tuck on the top.
  • It is slightly higher in the back and under the jaw line in the front.
• Spat
  • No spats should be used for the TCW Deathwatch builds.
  • Although due to CGI cheat in the show portrays some movement that could be considered less than hard armor, it has been decided it’s due to animation not actual portrayal.
• Flak Vest
  • The vest is Jango Fett style, navy blue in color.
  • This will be a leather or leather look fabric
• Boots
  • Palladium Boots Pampa high canvas are the best match found to date.
  • http://www.palladiumboots.com/cgi-bin/palladium/store/product_detail.html?mv_arg=x&pid=02352:060
• Gloves
  • The gloves should be blue in color and of a leather or faux leather material.
• Waist Wrap
  • Dark brown leather or leather look fabric approximately 1″ wider than ammo belt at top and bottom.
• Belt
  • The front piece of the belt is 1.5-inches wide.
  • The top piece has a ½-inch wide and 2.5-inch high pill-shaped hold cut in it.
  • A ¼-inch wide piece is located on either side of the ‘buckle.’ Then a 1-inch, then a ½-inch, then a 3-inch are located on either side of those.
  • The next pieces will be 2-inches wide and have a 1-inch wide 1-inch high square with rounded edges cut in it.
  • If the above measurements are not enough to place the sky blue stripes in the correct location, then modify them to do so.
  • The back of the belt will include similar pieces to cover the entire length. The back piece will be a 3-inch piece with a 2-inch wide, 2-inch high hole in the center as with the sidepieces.
  • Color gunmetal grey or charcoal grey.

• Jetpack
  • Must be the animated Deathwatch style jetpack.
  • The paint pattern should be silver/light grey or gunmetal with red accents as seen in the shown in the artwork
• Pistols
  • Westar-35
  • The pistols are silver/chrome in color.
  • The pistols may both be built of equal size to fit in the thigh holsters.
  • Refer to picture for the build.
• Carbine
  • A carbine can be carried in a similar design to the pistol, but more bulky.
  • Refer to this picture.