Don't like ads? Help support the Mercs by becoming a Supporter or Auxiliary Member today!
Official Members also get to use the forum ad-free - so kit up and join us!

 CRLs for Pre Vizsla

  • 2 Replies
  • 3373 Views

Thaxos


    *
  • Moose'alor
  • *
  • *
  • *
  • *
  • *
  • *
  • 14971
  • Beard'alor
  • Awards Award for 75 official invasions. Shock Infantry Brigade Member Heed the Call - helped the MMCC at a Star Wars Celebration Order of the Ori'Ramikad Celebration Orlando 2017
CRLs for Pre Vizsla
« on: Feb 21, 2014, 05:34 PM »
The Pre Vizsla CRL began as Praetor Ordo's build plan. With his permission, I have used it and modded it to fit CRL format.


PRE VIZSLA

Unless otherwise noted, the requirements are used for both real world and animated versions of this costume.

Requirements

SOFT PARTS

  • Flight Suit
    • The flight suit will be dark gray in color and have the standard Mandalorian double-sleeve.
    • The neck seal will be a straight tube with light padding inside of it. It has a small tuck on the top. It is slightly higher in the back and under the jaw line in the front.
    • There is a 2-inch blue stripe down the outside of both legs from the belt to ankle. There is a 1-inch edging above and below both knees.
  • Spat
    • Although there is some CGI cheat in TCW, there is NO correlation for the use of a spat.

  • Flak Vest
    • The vest is Jango Fett style, black in color.
    • This will be a leather or leather look fabric
  • Cape
    • The exterior of the cape is a light blue color with dark gray stripes stylized stripes.
    • There is a dark blue Death Watch sigil in the center on both sides.
    • It is clasp around the neck with a black band.
  • Boots
  • Gloves
    • Black in color
  • Waist Wrap
    • Dark brown leather or leather look fabric approximately 1" wider than ammo belt at top and bottom.
  • Belt
    • The front piece of the belt is 1.5-inches wide. The top piece has a ½-inch wide and 2.5-inch high pill-shaped hold cut in it. A ¼-inch wide piece is located on either side of the ‘buckle.’ Then a 1-inch, then a ½-inch, then a 3-inch are located on either side of those.
    • The next 3-inch piece will have a 2-inch wide sky blue stripe opposite the buckle (in line with the leg stripes).
    • The next pieces will be 2-inches wide and have a 1-inch wide 1-inch high square with rounded edges cut in it.
      • If the above measurements are not enough to place the sky blue stripes in the correct location, then modify them to do so.
    • The back of the belt will include similar pieces to cover the entire length.
    • The back piece will be a 3-inch piece with a 2-inch wide, 2-inch high hole in the center as with the sidepieces.
    • Color gunmetal grey or black.
    • Black Jango Fett style ammo belt can be used for "real world" armor.

    HARD PARTS

    For all armor parts, Valspar Graphite gray is the preferred color for the base color of the plates. However, gunmetal gray is an acceptable alternative.

    • Helmet
      • The dome and face is painted gunmetal gray.
      • The mandibles and band are a light gray or silver.
      • The cheeks and back are painted blue. Rustoleum Brilliant Blue is preferred.
      • The key slot dent is painted black with a white edge.
      • Finally, stylized three-claw emblem rises from the ring of the faceplate. Color should be Rustoleum Fossil lightly misted with yellow.
      • The helmet should have the narrower design with the longer face and the T should come to points at the ends.
      • There are no diamonds on the forehead of the helmet.
      • The right earcap must match the left. There is no RF.
      • A helmet of standard Modern Era Fett design, without Boba's dent, may be used on "real world" armor. The right earcap must be modded to match the left. There is no RF
    • Shoulder Plates
      • The shoulders are stylized shape, slightly curving inward on the sides. [/li
        • They are Rustoleum brilliant blue in color weathered through slightly with a gunmetal base.
      • The left has a red detail with a white edging ranks sigil. Refer to pix for details of sigil.
      • Standard Jango Fett template with applied sigils for real world armor.
    • Neck Plate/Gorget
      • The neck plate is stylized shape (flat across the bottom).
      • It is Rustoleum brilliant blue in color weathered through slightly with a gunmetal base.
      • Finally, there is a black 2-inch wide stripe in the center.
      • Standard Jango Fett pattern with proper colors and sigils for real world armor.
    • Left Chest Plate
      • The left chest plate is based on the WOF template, but it is in a stylized shape (flat across the top and a thicker ‘ear’).
      • It is gunmetal gray in color and weathered through slightly.
      • The chest slots are  should not be cut out .
      • The slots should be painted red and blue to match the artwork.
      • Standard Jango Fett pattern with proper colors and lighting for real world armor.
    • Right Chest Plate
      • The right chest plate is based on the WOF template, but it is in a stylized shape (flat across the top and a thicker ‘ear’).
      • It is gunmetal gray in color and weathered slightly.
      • Standard Jango Fett pattern for real world armor.
    • Diamond
    • The diamond is made from the WOF template.
    • The center rectangle is raised.
    • The color is sky blue with the edge weathered through to gunmetal.
    • The rectangle should be gunmetal.
  • Ab Plate
    • The ab plate is identical the WOF template.
    • It is gunmetal in color and weathered through slightly.
  • Back Plate
    • The back plate is identical to the WOF template and curved slightly around the torso at the edges (as per the WOF template).
    • It is Rustoleum brilliant blue across the upper back and gunmetal on the rest.
  • Cod Armor
    • The cod armor is in a stylized shape more of a triangle than the normal cod shape.
    • It is gunmetal gray in color and weathered through slightly.
    • Standard Boba Fett or Jango Fett pattern (no dents) for real world armor.
  • Thigh Armor
    • The thigh armor is a completely custom design and is stylized in shape and curved slightly around the leg.
    • The plate rides on the outside of the thigh rather than on the front of the thigh.
    • The holsters are built into the thigh plate and appear as part of the armor.
    • They are gunmetal gray in color, and have a Rustoleum brilliant blue stripe in line with the stripe on the flight suit, weathered through slightly.
    • Although a stylized piece, it is a representation of the era and characters. This piece MUST be replicated for real world armor.
    • Knee Plate
    • The knee plate is a completely custom design (based on the generic Mando knee) and is stylized in shape.
    • The face is more square and flat than normal.
    • The base color is gunmetal gray and the sides are Rustoleum brilliant blue and slightly weathered.
    • Standard Fett knee's, no dents, no dart launchers are acceptable for real world armor.
  • Shin Armor
    • The shin armor is based on the WOF template, but it is in a stylized symmetrical shape that is identical on both legs and both sides of the plate.[/li]
    • They are gunmetal gray in color with Rustoleum brilliant blue stripes on either side.
    • The blue stripes will begin at the flight suit stripe and go down either side of the face.
    • Standard Jango Fett pattern shins for real world armor.
  • Boot Armor
    • Required only for both animated and real world armor build.
    • Standard Fett pattern boot armor is to be used for real world style.
      • Stormtrooperguy designed a more accurately shaped set for animated style. Please contact him with inquiries.
    • Near the ankle, the armor should be sky blue in color.
    • The bottom 3/4 of the plate should be gunmetal in color and have an oval shape, not unlike a capital O.
    • It should be slightly weatherd through.
  • Hand Plates
    • The hand plates are a completely custom design in a ‘tombstone’ shape.
    • They are gunmetal gray in color and weathered slightly through.
  • Gauntlets
    • The gauntlets are a completely custom design.
    • They are a set of clamshell cylinder gauntlets.
      • There is a notch on the top which is approximately 3-inches wide and 1-inch long.
      • In front of it is a long box that is ½-inch high, 3-inches wide, and runs ½-inch from the edge of the elbow and wrist of the gauntlet.
      • Another ½-inch box fits on the top that is approximately 3/8ths of the length of the original box.
      • The edges all fade with a 60-degree edge except for the top that is a 45-degre angle.
      • There are two small rectangles on the top outside of each gauntlet.
    • They are gunmetal gray in color and slightly weathered through.
    • The right gauntlet must have the red sigil worn by the character.
    • This type of simple gauntlet is required for both animated and real world armor.
  • Jetpack
    • The Jetpack will be a custom fusion of the Jango Fett Geonosis "Arena" jetpack with the top missile is the missile from the Mitrinomon Z-6 Jetpack.
    • The paint pattern should be applied silver or gunmetal with red accents as depicted in the animated artwork(img).
  • Pistols
    • The pistols will be custom made based on the pictures of the blasters used in the television show.
    • The pistols are silver/chrome in color.
    • The pistols may both be built of equal size to fit in the thigh holsters.
    • Refer to this picture for the build.
    • Due to the portayal of sound in the animated series, Westar 34's (Jango Fett's guns) may be substituted on real world armor.
  • Darksaber
    • The darksaber is a required component of the Pre Vizsla Build animated or real world.[/li]
    • No blade is required, only the hilt.
      • The handle of the darksaber is rectangular.
      • The darksaber hilt is much longer than the traditional lightsaber hilt.
      • It is gunmetal or black in color.
      • There is a rectangular shaped pommel guard approximately 3/4 up the overall length of the handle.
      • The pommel guard slopes upwards on the front side of the saber.
      • The portion of the hilt extending beyond the pommel guard is ribbed and silver in color.
      • There is a small rectangular shaped emitter at the top of the hilt.
      • This emitter is wedge cut and hollow.
      • The darksaber must ride over the right shoulder on the under the jetpack.
      Refer to this image
  • Lightsaber
    • An Obi Wan Kenobi replica lightsaber may be worn attached to the belt on the left hip.

« Last Edit: Sep 19, 2017, 04:36 PM by Ref Al'drann » Logged
The Rules and Guides board has everything you need to learn how to utilize the forums!

Does your signature look cut off? Here's why!

Solus Raam


    *
  • Sukwee Vawd
  • *
  • *
  • *
  • *
  • *
  • 3781
  • Controlled Chaos
  • Awards Award for 50 official invasions. Order of the Ori'Ramikad Ground Pounder - Official Member with the most recorded invasions 267th Rapid Assault Poster Boy - Official Member appears in costume in the most photos
Re: CRLs for Pre Vizsla
« Reply #1 on: Nov 24, 2014, 09:36 AM »
Do there need to be any updates for the Season 4 and 5 Pre Vizla or just the helmet update?

Logged
Official Troop Count: 70

bravoleader


    *
  • *
  • *
  • 417
  • For Mandalore!
  • Awards Award for 10 official invasions. Clan with the most recorded invasions in 2016/2017 TCW and Rebels Canon Mandalorians Hard Contact - Clan with the most recorded invasions
Re: CRLs for Pre Vizsla
« Reply #2 on: Nov 24, 2014, 10:03 AM »
Hello Solus.
I sent what I wrote for the 501st regarding Pre Vizsla S4/5 CW CRL to Kelan Ord.
If you need, you can ask him to forward it to you for a check (that should be done I think)
In the meanwhile...
I also added this thread in the Canon Brigade with pics to my photobucket and there's also the link to the photobucket with armor parts details with no background that could be used in the CRL.
http://mandalorianmercs.org/forum/index.php?topic=84126.msg1254104#new"
Hope this could help

F

 


Don't like ads? Help support the Mercs by becoming a Supporter or Auxiliary Member today!
Official Members also get to use the forum ad-free - so kit up and join us!




Powered by EzPortal