General Armor Requirements

• All armor must be made of solid materials such as fiberglass, styrene, sintra, or vacuum-formed ABS.
• Armor must have dimension and give the appearance of thickness and depth as per the visual references of this character.
• All armor and soft parts must be weathered where indicated in visual references to give the illusion of battle wear and damage.

Helmet

• The helmet is a specific female Mandalorian commando helmet style seen in Clone Wars Season 7.
• The helmet has a yellow T-visor with a black T-visor outline/mandible.
• The dome is muted red with three vertical black lines starting at the back slightly above the dome ridge.
• On the front, the two outside lines/shapes are mirrored, with the outside edge longer than the inside edge.
  • Each black line has a red line closer to the inside, matching the black shape on the front.
  • The middle black line ends in an upside-down pentagon, with the middle red line ending in an arrow shape within the pentagon.
• The cheeks are muted red with a bright red cheek outline.
• The rear band has a dark red upper part connected with the dark red outline of the cheeks and is muted red before transitioning to black.
• The rear part of the helmet is black.
• The keyslots are dark grey/black with a red border connected with red symmetrical lines, evenly spaced, and connected on the side via a straight vertical line.

Flightsuit

• The flightsuit is tight-fitted and made of stretch black or charcoal fabric such as cotton stretch, heavy jersey, or spandex (not shiny).
• The flightsuit features grey piping detail on the inside of the arm, starting under the short sleeve of the flak vest, curving above the elbow towards the back, and stopping at the middle of the inside sleeve.
• The flightsuit has a high collar.
• The sleeves are visible under the gauntlet, covering the gloves slightly, and finished with a rounded edge.

Gloves

• The gloves are two-tone with a black bottom and grey top.

Flak Vest

• The flak vest is black or charcoal, tight-fitted, and made from the same material as the flightsuit.
• The flak vest has short sleeves finished with grey piping detail/border.
• The collar has a grey border attached, against the collar bones.
• There is one grey rectangle and three small squares on the bottom center of the vest.
• Wearer may utilize a one piece flight suit without a flak vest, provided the piping details give the appearance of a short sleeve flak vest.

Boots

• The boots are thigh-high and black with a leather-like appearance.

Chest Armor

• The chest armor consists of separate left and right chest plates with two pentagon-shaped upper plates.
• Chest plates have a + shaped black outline dividing the plates visually.
• The pentagon-shaped plates have a yellow (light-up) triangle on each side that connects to the Epaulettes.
• The ab armor consists of six separate trapezoidal-shaped pieces (three on each side) tapering towards the middle.
• Ab armor also consists of 1 rectangular piece of armor and 3 square pieces of armor mounted inline with the bottom 2 sets of trapezoidal ab plates.
• The chest and ab armor are painted in a muted red/auburn color and weathered to match visual references.
• Two Epaulettes connect to the chestplate, going over the shoulders and connecting to the jetpack on the back.
  • Epaulettes are muted red/auburn with grey detailing on the edges.

Back Armor

• The back armor consists of six separate trapezoid-shaped pieces (three on each side) pointing up towards the middle.
• Back armor is mounted below the jetpack such that it is visible when jetpack is worn.
• The back armor is painted in a muted red/auburn color.

Shoulder Armor

• The shoulder armor is three-dimensional with a flat curved top the width of the wearer’s arm and squared off sections extending down to cover the front and back.
• Shoulder armor sits above the actual shoulder, lifted by adding padding under the armor.
• The right shoulder armor has a hand stamp detail in black (Shadow Collective’s black hand).
• The left shoulder plate has a skull detail in black.
• The shoulder armor has a bright red outline.

Gauntlets

• The gauntlets are tube-style with no visible means of closure.
• The gauntlets are painted muted red with a bright red outline.
• The gauntlets have a thin top layer, smaller towards the elbow and wider towards the wrist, creating a Z-shape.
• Gauntlets feature a silver comm pad section close to the wearer’s wrist.
• There is a rectangle detail piece on top of the gauntlet, making a smooth transition to the com pad.

Codpiece

• The codpiece consists of three pieces: two mirrored outside pieces and one elongated hexagon shape.
• The top border of the codpiece has a vertical rectangle piece.
• The codpiece can be made as a one-piece armor with painted black lines.

Thigh Armor and Kama

• The kama is muted red, matching the armor, and made of heavy fabric like canvas with fusible interfacing for shape.
• Each side of the kama has a long tip extending to the back, horizontal across the behind, with a red outline.
• The kama has black rectangles across the front, becoming longer towards the bottom point (seven rectangles in total).
• The kama has a black circular connection point for the Westar Blasters.
• The side pieces of the kama are kept in place by a strap around the thighs.

Knee Armor

• The knee armor has a rectangular shape with dimensional, slightly rounded corners on the bottom.
• The knee armor is painted muted red.
• The knee armor is secured with a matching strap around the knee.
• Knee armor strap features a grey stripe on top and bottom wrapping around the sides of the wearer.

Shin Armor

• The shin armor is attached with a grey (or red) strap around the ankle and upper part of the calf for a snug fit.
• The shin armor consists of a long straight section with a curvature reaching from the ankle to just below the knee, wider on top and wrapping halfway around the leg.
• The bottom to middle part of the shin armor is painted a darker muted red with an oval/circular shape, transitioning to a lighter muted red matching the knees on the upper part.

Cummerbund and Belt

• Belt is a red cummerbund with grey detailing matching the red of the armor.
• Belt features two grey outlined trapezoids in the front. The upper trapezoid is outlined in bright red, the lower trapezoid is outlined in grey.
• Belt extends up and under the flak vest when worn.

Jetpack

• The jetpack is the Clone Wars Season 7 specific design.
• Jetpack features a symmetrical design with two cylindrical thruster sections mounted on the outside of the main body.
• The main body of the jetpack is black on top and grey on bottom following the panel detailing.
• The jetpack features 2 yellow detail squares on the black body section, mounted close to the thruster tubes.
• The thruster sections are cylindrical with ogive rocket tops, conical thrusters, and pyramidal fins.
• The rockets have black and red tips.
• There are two red rectangle lights on each side of the jetpack.
• The jetpack is painted black and grey.
• Jetpack has no visible means of attachment.

Weapons

• The character carries two animated style Westar 35 blasters.
• Westar blasters are grey and silver to match visual references.

Wig (optional)

• If no wig is worn, the helmet must remain on at all times.
• The hair should be purple in color to match references.
• The hair is a layered bob that ends just before the jawline. Bangs sweep towards the left brow.